Start to prepare for C_TS422_2021 SAP Certified Application Associate - SAP S/4HANA Production Planning and Manufacturing exam? Passcert provides SAP S/4HANA Production Planning and Manufacturing C_TS422_2021 Dumps that include all you need to prepare for and pass the SAP C_TS422_2021 exam on your first attempt. The SAP S/4HANA Production Planning and Manufacturing C_TS422_2021 Dumps are the real exam questions that will assist you in SAP C_TS422_2021 exam preparation and enable you to pass the final SAP C_TS422_2021 certification exam successfully. Try the real and accurate SAP S/4HANA Production Planning and Manufacturing C_TS422_2021 Dumps to pass C_TS422_2021 certification exam with good scores.

The "SAP Certified Application Associate - SAP S/4HANA Production Planning and Manufacturing" certification exam validates that the candidate possesses the fundamental and core knowledge required of the SAP S/4HANA Manufacturing consultant profile. This certification proves that the candidate has an overall understanding and in‐depth technical skills to participate as a member of a project team in a mentored role.

Exam Code: C_TS422_2021

Exam Name: SAP Certified Application Associate - SAP S/4HANA Production Planning and Manufacturing

Exam: 80 questions

Cut Score: 54%

Duration: 180 mins

Languages: German, English, Japanese, Chinese

Advanced Planning in SAP S/4HANA > 12%

Production Orders in SAP S/4HANA > 12%

Master Data in SAP S/4HANA > 12%

Material Requirements Planning in SAP S/4HANA  8% - 12%

Lean Manufacturing in SAP S/4HANA  8% - 12%

Capacity Planning in SAP S/4HANA   8% - 12%

Demand Management in SAP S/4HANA < 8%

Introduction to SAP S/4HANA Production Planning < 8%

Introduction to SAP S/4HANA Supply Chain Planning < 8%

Process Orders in SAP S/4HANA < 8%

In the Capacity Scheduling Table, which settings can you select for the planning strategy? Note: There are 3 correct answers to this question.

A.Planning mode

B.Finiteness level

C.Fixed pegging

D.Direction

E.Scheduling control

Answer : A, D, E

What determines whether the planned independent requirements in demand management are consumed by other requirements? Note: There are 2 correct answers to this question.

A.Requirements type

B.Order type

C.Planning strategy

D.Requirements profile

Answer : A

Which chart types does the tabular planning table for capacity planning provide in SAP S/4HANA? Note: There are 2 correct answers to this question.

A.Orders (dispatched) chart

B.Capacity requirements chart

C.Order (pool) chart

D.Work center capacities chart

Answer : B, D

Your project team decides to use a make-to-order planning strategy for a strategic material in discrete manufacturing. What is the impact of this decision? Note: There are 3 correct answers to this question.

A.Production orders are created with sales order reference.

B.Sales orders have to be ATP-confirmed (available-to-promise) to be saved.

C.Net requirements calculation is carried out for every sales order individually.

D.Storage location MRP areas are required for sales-order-specific stock.

E.Both the reduction of make-to-order stock and requirements occur on delivery.

Answer : A, B, C

Which alternative item strategies are available in bills of material (BOMs) in SAP S/4HANA? Note: There are 2 correct answers to this question.

A.Manual maintenance

B.Simultaneous

C.100% check

D.First in first out (FIFO)

Answer : A, C

When do you use variant bills of materials (BOMs)?

A.When a material has a configurable BOM

B.When multiple materials also have similar BOMs

C.When a material has multiple BOMs

D.When multiple materials have multiple BOMs

Answer:D

Which of the following elements does MRP take into account during net requirement calculation?

A.Purchase orders

B.Lot size

C.Maximum stock level

D.Safety stock

Answer:B, D

You set up a material as a phantom assembly by entering the special procurement key in the material master. How can you switch off the phantom assembly in a specific bill of material (BOM)?

A.Change the special procurement key of the phantom assembly in the BOM.

B.Change the explosion type of the phantom assembly in the BOM.

C.Change the phantom item indicator for the phantom assembly in the BOM.

D.Change the item category of the phantom assembly in the BOM.

Answer:B